Quick Answer: How Much HP Does Vortec Heads Add?

What is the difference between Vortec heads and regular heads?

The Vortec heads are a little bit lighter than the older heads and have a “kidney” or “heart” shaped combustion chamber that is more efficient than the double hump chamber.

The L31 Vortec comes in two different casting numbers, 10239906 (#906) or 12558062 (#062)..

Will 327 heads fit on a 350?

They are perfect for a 350. Both the 327 and the 350 have a 4″ bore so they like the same heads. Old heads like that will have softer valve seats, so if you want them to last a long time, you should either replace the seats or run leaded gas in the engine.

How much HP does a cam add to a 350?

Replacing the 2G with a Q-Jet and intake alone can be worth 25-30 hp. Toss in a mild cam and cylinder head upgrade and the power gains really start to add up.

Is a 400 small block better than a 350?

A small block 350 and a 400 have an identical block design. Most accessories will fit either engine. The major difference is found in the casting numbers and the way they are balanced. Most 350 cubic inch engines are internally balanced whereas the 400 engines are not.

What year is the best Chevy 350 engine?

L31 (2002) From a purely technical standpoint, the most recent version of the Chevy 350 would naturally be the best of the bunch. Marketed as the “Vortec 5700” engine, but known internally by the moniker of L31, this engine was used primarily in GM vans and trucks until 2002.

Do aluminum heads make more power?

Aluminum heads will dissipate heat faster. This allows for higher Compression Ratios with less risk of Detonation. The cooler head also delivers a cooler air/fuel mixture to the combustion chamber. Cooler air is denser and can make more power.

How big of a cam can I put in a stock 350?

the cam can be as big as you want nearly but if it doesn’t match the CR, intake etc. it’s pointless and will run bad. if you want the most power get it to match what you have now. the 270h should have around 9.5 or so CR and they don’t make it solid that i know of.

How much HP do heads add?

A set of heads for your car will probably set you back $700. Your engine probably won’t breath much better because of your cam, the smaller combustion chamber might bump your compression up a couple of points. You might get 20 hp or so.

How much horsepower would a stock 400 SBC with Vortec heads?

376 hpWith the stock Vortec heads, the low-compression 400 managed to make 376 hp and almost 450 lb-ft of torque.

Can I put Vortec heads on a 350?

If you wanted the Vortec heads on your engine then you would have to buy a new intake manifold to be able to get the TBI set-up onto the heads. … But you would need to buy a TBI intake manifold to bolt up to the Vortec heads. You can’t by a spacer for the Vortec intake manifold.

Does adding a cam increase horsepower?

Performance cams increase the duration and timing of the valve openings during the engine stroke, increasing horsepower and making your car accelerate more quickly. You’ll idle slightly rougher with a performance cam, but get a throaty rumble that’s desirable for some gearheads, depending on your vehicle.

What makes Vortec heads so good?

The L31 Vortec heads have larger ports than the older Gen I cast steel heads, so they outflow the older heads. The Vortec heads are a little bit lighter than the older heads and have a “kidney” or “heart” shaped combustion chamber that is more efficient than the double hump chamber.

How much HP can Vortec heads make?

GM Vortec cylinder heads are used with a Comp Cams Xtreme Energy 262° camshaft to produce 390 HP and 426 ft-lbs of torque. These numbers are made with 87 octane, while most of the combos on my site used 92 or 93 octane gasoline.

Are Vortec heads worth it?

vortec heads are one of the cheapest hp gain and they’ll give you better gas mileage. For the center bolt valve covers the ones for the vortec heads are taller then the center bolt valve covers you find on non-vortec heads.

Can you put 400 heads on a 350?

The only difference is that 400 heads have steam holes drilled in them for the 400 block. You can put 400 heads on a 350 but you should not put 350 heads on a 400 without drilling the steam holes.

What’s the difference between a 350 and a 350 Vortec?

Vortec heads instantly added 55 or more horsepower to a regular 350 head with the same displacement. Automotive enthusiasts are quick to note that the 350 and the 5.7 Vortec are essentially the same engine with the same displacement. The 350 designation is the cubic inch measurement that also translates to 5.7 liters.

Can you put 350 heads on a 305?

Virtually any 350 heads will work on a 305. The high compression 350 heads are similiar in combustion chamber size & intake valve size to the 305 heads & will give a 305 the same performance as if using 305 heads.

What are the best small block Chevy heads?

Peak Torque and HorsepowerCylinder HeadPeak HorsepowerPeak TorqueEdelbrock395 at 5,900 rpm409 at 4,200 rpm (5)Speedway381 at 5,400 rpm409 at 4,200 rpm (5)Vortec378 at 5,300 rpm408 at 4,300 rpm (7)Stock Iron358 at 5,800 rpm379 at 4,300 rpm (8)4 more rows•Jul 12, 2012

How much HP can you get from a 350?

a typical 350 Chevy can make upwards of 350 – 375 HP before you exceed the reliability of the components. For a big block with the same stock components it can make in the area of about 400 to 475 or so HP and handle upwards of about 500 HP before you exceed the reliability of the stock cast pistons.

Are Vortec heads better than double hump heads?

The Vortec heads are a little bit lighter than the older heads and have a “kidney” or “heart” shaped combustion chamber that is more efficient than the double hump chamber.

Do aluminum heads add HP?

Aluminum heads will not automatically create more power than iron heads unless they flow more air and are installed on a higher compression ratio engine. … In some cases the engine would have produced more power with a set of well ported, iron heads, and at a lower price.