- Do ball joints need to be torqued?
- What is the torque on ball joints?
- Do I need an alignment after replacing ball joints?
- Are ball joints expensive to replace?
- Can tie rods be tightened?
- Can bad ball joints cause tight steering?
- How do you loosen a tight ball joint?
- Is it dangerous to drive with a bad ball joint?
- How long do ball joints last?
- What is the torque for tie rod ends?
- Can you drive a car with a bad ball joint?
- How long does it take to replace lower ball joint?
- Should I replace upper and lower ball joints at the same time?
- Why are ball joints tapered?
- How often should you grease your ball joints?
- How much does it cost to fix a worn suspension joint?
Do ball joints need to be torqued?
It is vital to torque ball joint stud nuts to proper specifications.
Improper torquing will cause looseness that may eventually cause joint stud breakage and damage to the steering knuckle..
What is the torque on ball joints?
Many ball joints may have an initial torque spec as low as 15-30 ft/lbs and torque angles are between 140º and 225º.
Do I need an alignment after replacing ball joints?
No, you certainly don’t need alignment after ball joints, unless your previous alignment was done when ball joints were bad and loose. If your car is driving sloppy after ball joints replacement, check other suspension parts.
Are ball joints expensive to replace?
The cost of replacing ball joints is dependent on the type of car you drive. Different makes and models require different parts. The average ball joint replacement cost is anywhere from $500 to $700. Another important factor that will affect the cost is how much damage is done to the system and the ball joints.
Can tie rods be tightened?
Inner tie rods can be tightened but this is not something that should be done by a professional shop for a customer as it would be considered an improper repair. For a DIYer it can work fine. The tie rod is removed from the steering rack and put into a press and recrimped with a heavy metal sleeve.
Can bad ball joints cause tight steering?
Steering – Worn ball joints can affect your vehicle’s steering, usually making the steering sloppy or stiff depending on how the ball joint is wearing. … However, if both edges are wearing out faster than the middle, the problem is not ball joints, but under-inflation of your tires.
How do you loosen a tight ball joint?
Sand it a bit. edit- The ball itself. yep, best way is to get the ball out the joint then sand the ball lightly, then refit the fall and if it is still too tight try again, it’s easy enough to just tighten it again.
Is it dangerous to drive with a bad ball joint?
Ball joints play a major role in the steering and suspension of cars and can last a long time. However, driving on bad ball joints can cause major damage and total ball joint failure can be fatal. If you’re unsure about the condition of the ball joints in a car, then speak to a garage about good quality replacements.
How long do ball joints last?
Generally speaking, you should expect to have to have your ball joints replaced between 70,000 to 150,000 miles of driving. Excessive play in the joint can cause additional wear, and if a ball joint fails, your car’s suspension could collapse and you could lose control of the vehicle.
What is the torque for tie rod ends?
Reassemble outer tie rod end to spindle tighten outer tie rod end nut to 36 ft. -lbs. (49 N-M). Do not turn nut more than 1/6 turn beyond the specified torque.
Can you drive a car with a bad ball joint?
It is never recommended to drive with a bad ball joint. … A bad ball joint results in excessive vibration in the suspension system, clicking noise from the front part of your vehicle, uneven tire wear, and steering wandering and vibrating.
How long does it take to replace lower ball joint?
The ball joint is a small part of your car, and the part itself is only going to cost between $20-$150 or more, depending on where you get it from and what kind of vehicle you own. It can take a little over an hour to get it replaced, so the full ball joint replacement cost will be between $100 and $400.
Should I replace upper and lower ball joints at the same time?
Many technicians recommend replacing both joints at the same time (both lowers, both uppers or all four). Another item that should be checked when ball joints are replaced is the stud hole in the steering knuckle — especially if the ball joint stud has broken or is loose.
Why are ball joints tapered?
With skill, no damage is done to the joint, boot or knuckle. One sharp blow to the knuckle causes the taper to distort slightly. This separates the components quickly and without permanent damage. The method requires a great deal of finesse and takes time to learn.
How often should you grease your ball joints?
If no bleed hole the once every 2 years and do not overfill.
How much does it cost to fix a worn suspension joint?
Kloster: Replacement costs depend on the year, make and model of your vehicle. There are many different vehicles on the road today and costs can range from $200 [for one] to just over $1,000 [for all four], including an alignment. Some vehicles have only two lower ball joints and some have four, both upper and lower.